News

DC SPORTS: 2013 Scion FRS / Subaru BRZ DCS-Dual Canister Catalytic Back Exhaust System

LAUNCH Distribution is excited to announce the arrival of the NEW 2013 Scion FRS / Subaru BRZ DCS-Dual Canister Catalytic Back Exhaust System by DC SPORTS to our motorsports line.

It is constructed of T304 stainless steel, fully polished to a show quality finish. Featuring cast flanges for its superior strength and leak-free seals, comes with 2.5 inch piping to dual 2.5 inch round tank mufflers, it is finished off with a single DC sports logo engraved 4 inch tip on each side. All necessary hardware is included for a quick, easy worry free installation. This exhaust features our new Passive Resonance Chamber (PRC) to “tune” the tone and adjust the harmonics so it’s pleasing but doesn’t affect performance. Sizing is calculated so certain tones reflected by the Passive Resonance Chamber (PRC) cancel out unwanted frequencies. Throttle response is enhanced, adding a growl of authority under acceleration while providing a reasonable tone at cruising and idle. The DC exhaust adds a much needed voice to the aggressive looks and sporty handing that comes on the FRS-BRZ. Tested, designed and developed in house by DC Sports.


Part# DCS7049

• Lowers backpressure to increases throttle response – Allowing engine to breathe easier
• Adds an aggressive tone under acceleration
• T304 stainless steel w/ high polish finish
• Easy bolt on installation
• Industry standard one year warranty
• DC Sports quality

Data Specs:

Material: T304 Stainless Steel
Piping Size: 2.5 inch (63.5mm)
Tip Size: 4 inch (102mm)
Configuration: Dual Canister w/ Dual Tips (one per side)
Muffler Diameter: 2.5 inch (63.5)
Fitment Position: Utilizes OEM hanger positions
Hardware: all necessary hardware included (instructions, gaskets, bolts and nuts)
Installation time: approximately 1 hour.

Part# SCD7049
• Lowers backpressure by replacing catalytic converter – Allows the engine to breathe easier
• T304 stainless steel w/ high polish finish
• Easy bolt on installation
• Industry standard one year warranty
• DC Sports quality
• For competition off-road use.

Data Specs:
Material: T304 Stainless Steel
Piping Size: 2.5 inch (63.5mm)
Fitment Position: Utilizes OEM positions
Hardware: all necessary hardware included (instructions, gaskets, bolts and nuts)
Installation time: approximately 1/2 hour.

Coming soon!!!

Part# CSB1407 (aprox 1 week)
• Solid one piece design
• Significantly increases front end chassis rigidity
• High strength mild steel construction
• Durable powder coated finish
• Easy bolt on installation
• Industry standard one year warranty
• DC Sports quality

Data Specs:
Material: Mild Steel
Tubing Size: 1.25in (32mm) diameter tubing
Fitment Position: Utilizes OEM mounting positions
Hardware: all necessary hardware included (instructions, bolts, spacers and washers)
Installation time: approximately 1/2 hour.

Part# SOP7049 (aprox 6-8 weeks)
• Allows the engine to breathe easier
• T304 stainless steel w/ high polish finish
• Easy bolt on installation
• Industry standard one year warranty
• DC Sports quality
• For competition off-road use.

Data Specs:
Material: T304 Stainless Steel
Piping Size: 2.5 inch (63.5mm)
Fitment Position: Utilizes OEM positions
Hardware: all necessary hardware included (instructions, gaskets, bolts and nuts).

Installation time: approximately 1 hour.

PLACE YOUR ORDER

Contact your LAUNCH Sales Rep for pricing and availability at (626) 839-7150.

Lazer Star: New Product Added to Inventory

LAUNCH Distribution is proud to announce the arrival of Lazer Star Lights to our vastly growing lighting inventory.
Lazer Star lights are available for Cars, Trucks, Off-Road, Marine, ATV, Motorcyles, and more. Lazer Star offers a wide range of lighting that include LED light bars, HID, and Halogen lights with an array of colors.

About:
Weekend Concepts, Inc. has been a pioneer in billet lighting systems since the introduction of the Lazer Star “Bullet” Billet Light in 1993. Lazer Star Billet Lights are the pinnacle of small, attractive, functional lighting systems for the Harley-Davidson and cruiser motorcycles, along with ATV’s, Sand Rails, and Street Rods. Lazer Star Billet Lights have set the standard to which many have tried to imitate, but none can duplicate. Lazer Star products are manufactured in our facility in Paso Robles, California, then packaged and shipped to points all over the world. The original Bullet, for instance, has been upgraded and improved many times since its introduction, with the latest being the development of LED technology. The Shorty, Micro B and XS designs have all developed from the original Bullet design and are constantly improved on. All our lamps, halogen and LED are specifically manufactured to our specifications, including our 100 watt spot lamp, which was designed exclusively for us.

Place your order
Speak with our experienced sales staff about Lazer Star lights pricing and available applications at (626) 839-7150.

aFe Power: 2011-13 Dodge Charger Challenger and Chrysler 300C Intake Sys

LAUNCH Distribution is proud to announce the release of the new Stage 2 cold air intake system for the 2011-2013 Dodge Challenger, Charger and Chrysler 300C V8-5.7L from aFe Power.

This cold air intake system produced 17 max horsepower, 17lbs. x ft. torque and out-flowed the factory intake by 40%. Included in this cold air intake system kit is a 16 gauge powder-coated heat shield, a massive 8” tall aFe Power filter, and a CAD designed, rotomolded intake tube.

This is a direct bolt-on kit and requires no cutting or drilling.

Order Now!
Available in Pro 5R Oiled Filter (P/N 54-12162) or Pro Dry S Dry Filter (P/N 51-12162)
Contact your LAUNCH Sales rep at (626) 839-7150.

aFe Power: MACH Force XP Turbo-Back Exhaust System for 2003-2004.5 Dodge RAM

LAUNCH Distribution announces a new release of a MACH Force XP Exhaust System for the 2003-2004.5 Dodge RAM 2500/3500 L6-5.9L (td) Cummins by aFe Power.

The MACH Force XP exhaust is engineered to perform in the most extreme environments. This system is constructed from 5″ mandrel bent 409 stainless steel tubing for maximum flow, increased horsepower, increased torque and lower EGT’s. This system is available in 5″ turbo-back with muffler and 6″ powder-coated black tip. MACH Force XP exhaust systems are the perfect combination of performance, fit and value.

Installation is a Snap:
All systems use factory mounting locations providing stability and hassle-free installation.

Leak-Free Seal:
High quality OE style flange and band clamps are used for a complete 360 degree sealing surface.

Aggressive Sound:
A free-flowing 24″ long muffler is used to absorb high pitch tones producing a powerful sound and unleashing all available horsepower and torque out of your rig.

OE Fit:
OE style bayonet hangers are used to maintain a stable pipe location during high vibration and high heat conditions. The Bayonet tip holds the hanger bushing in place for an OE style fit that does not change with time.

Flow and Performance:
Mach FORCE XP exhaust systems are constructed of 5″ mandrel bent stainless steel tubing for maximum flow. Smooth transition bends allow for low turbulence, increasing horsepower, torque and lowering EGT’s.

Powder Coated Black Tip:
Finishing off the exhaust is a powder-coated black 304 stainless steel slash cut exhaust tip. This tip features a drain port on the bottom to keep rust and corrosion away.

Does Not Fit Cab & Chassis.

Note: This is a “Race Only” product used solely for competition. Its use is limited to closed-course and open-course racing that is formally sanctioned by a recognized racing organization. Any other use including recreational off-road use could be in violation of local, state and federal laws.

Place your order
Call your LAUNCH Distribution Sales person for availability and pricing at (626) 839-7150.

Clutch Masters: NOW Available at LAUNCH DIstribution

LAUNCH Distribution is proud to announce the arrival of Clutch Masters performance clutches and flywheels to our motorsports lineup.

Contact your LAUNCH Sales rep for available applications and pricing today at (626) 839=7150.

ABOUT
Clutch Masters

High Technology Makes the Difference
Historically, high performance clutches have been a compromise. While improving holding or clamping pressure, manufacturers nearly always increase pedal pressure to an uncomfortable point, especially for stop-and-go traffic.

Besides drivability concerns, additional pedal pressure can adversely affect stock clutch linkage and cause premature thrust bearing wear, leading to missed shifts, damaged clutch components and even engine destruction.

Today, thanks to Clutch Masters, increased holding pressure does not necessarily mean increased pedal pressure and the problems that can accompany it. By re-engineering the leverage or fulcrum point on the pressure plate through their Hi-Leveragetm ttechnique, Clutch Masters has increased clamping power, often without changing pedal pressure.

Excessively increased pedal pressure, as found in many of today’s traditional high performance clutches, places an unsafe amount of pressure on the delicate crankshaft thrust bearing found in most of today’s sport compact automobiles. Placing undue stress on the thrust bearing typically causes the bearing to wear prematurely or fail altogether. This failure can lead to catastrophic internal engine damage.

A clutch, simply put, is a friction device that disengages and engages the engine from the transmission to allow for transition from motionless to movement and for gear changes. For street applications a smooth transition of power is essential while still being able to transfer all the power of the engine to the transmission. As power output of engines increase and demands on clutches become greater – for example high performance street or racing cars – the holding and clamping capacity of a clutch also must increase. This is where Clutch Masters’ innovative engineering comes into play.

Simply the Best…

aFe Power: Twisted Steel Header for 2001-2006 BMW M3 (E46)

LAUNCH Distribution is proud to introduce the all new headers for the popular 2001-2006 BMW M3 (E46) with the L6-3.2L S54 engine from aFe Power.

(P/N: 48-36306)
aFe Power’s new “Race Only” Twisted Steel Headers deliver an astounding 12hp and 16lbs. x ft. torque while outflowing the factory exhaust manifolds. The headers are constructed of near equal length 1.625” 16-gauge 304 stainless steel tubing with 3/8” thick CNC machined flanges to ensure a leak free seal. To eliminate dead space that can cause turbulence and hinder flow that formed collectors are prone to produce, true merge collectors and optimized tube lengths are used for true pulse control technology improving flow and performance. 100% TIG-welded, the smooth curves and increased diameter of this header helps remove restriction and keeps exhaust gas flowing smoothly for improved performance and durability. All components are supplied for a hassle-free installation with no modifications necessary.

Tig-Welded:
100% TIG-Welded by certified craftsmen for race proven strength and durability. TIG-Welding provides the strongest welds reducing stress cracks.

Retain Factory Sensors:
aFe has designed this system to retain all your factory sensors for a hassle free installation.

Mitered Collectors:
Mitered collectors not only extend the tube lengths and decrease turbulence, but provide optimal exhaust scavenging. The result is increased horsepower, torque and improved throttle response.

CNC Machined Flanges:
Flanges are CNC machined not only to be visually appealing but for a precise fit and leak-free seal.

Brushed 304 SS Construction:
These headers are constructed of durable CNC mandrel bent brushed 304 stainless steel tubing for maximum performance, corrosion resistance and strength eliminating cracking.

Note:
This is a “Race Only” product used solely for competition. Its use is limited to closed-course and open-course racing that is formally sanctioned by a recognized racing organization. Any other use including recreational off-road use could be in violation of local, state and federal laws. A check engine light will emitt and aFe recommends using a programmer but it is not necessary.

Also Fits:
BMW Z3 M (E36) 01-02 L6-3.2L S54
BMW Z4 M (E85/86) 06-08 L6-3.2L S54

Place your order NOW!
Call your LAUNCH Sales person today at (626) 839-7150.

aFe Power: MACH Force XP Exhaust System for 1999-2003 GM Trucks

LAUNCH Distribution welcomes the release of a MACH Force XP Exhaust System for the 1999-2003 GM Gas Trucks V6-4.3L/V8-4.8/5.3L by aFe Power.

This MACH Force XP Cat-Back exhaust system produces an astonishing 9 horsepower and 15lbs. x ft. torque. This cat-back exhaust is constructed of 3″ mandrel-bent 409 stainless steel and comes complete with free-flowing muffler, tubing, OE style bayonet hangers, band clamps and all hardware necessary for a hassle-free installation. The smooth curves and increased diameter of this exhaust system helps remove restriction and keeps exhaust gas flowing smoothly for increased horsepower and torque. The system is finished off with a aggressive black 304 stainless steel, rolled slash cut tip for an aggressive style.

Installation is a Snap:

This MACH Force XP uses all factory mounting locations providing stability and a hassle-free installation.

Leak-Free Seal:
High quality OE style flange and band clamps are used for a complete 360-degree sealing surface eliminating leak paths.

Aggressive Sound:
A straight through designed, free-flowing stainless steel muffler is used to absorb high pitch tones producing a powerful sound and unleashing all available horsepower and torque out of your rig.

Perfect Fit:
OE style bayonet hangers are used to maintain a stable pipe location during high vibration and high heat conditions. The Bayonet tip holds the hanger bushing in place for an OE style fit that does not change with time.

Flow and Performance:
MACH Force XP exhaust systems are constructed of 3″ mandrel bent stainless steel tubing for maximum flow. Smooth transition bends allow for low turbulence, increasing horsepower, torque and improving throttle response.

Place your order
Contact your LAUNCH rep today for pricing and availability at (626) 839-7150.

Turbosmart: Nissan R35 GTR Internal Wastegate

LAUNCH Distribution is proud to announce the arrival of the Nissan R35 GTR Internal Wastegate Actuator from Turbosmart.

Overview:
Actuator (IWG) kit provides better turbo response and greater sensitivity when
managing boost pressures. Designed as a direct bolt-on replacement for the factory part, the Nissan R35 GTR IWG kit is
easy to install and requires no special tools or fabrication. It canʼt get any easier!

Features:
• Silicon diaphragm with Nomex reinforcement to withstand high temperatures.
• High grade, billet aluminum construction.
• Stainless steel rods and connecting clevis for corrosion resistance.
• Locking Collar design cap allows for quick spring changes.
• Ideal for use with any Turbosmart boost controller.

Applications:

• Nissan R35 GTR 2008-current

Part Numbers:
TS-0615-2072 7 PSI / 0.5 Bar

Place your order
Call your LAUNCH sales rep for pricing and availability at (626) 839-7150.

aFe Power: Bladerunner for 2011-13 Ford F150

LAUNCH Distribution is proud to announce the arrival the Bladerunner Charge Pipe for 2011-2013 Ford F150 Ecoboost V6 from aFe Power.

The aFe charge pipe represents the next generation of gas truck performance products. Our BladeRunner charge pipe is a 3”-3 1/2” CNC mandrel bent black powder-coated aluminum tube. The charge pipe increases flow while adding 10 horsepower and 12lbs. x ft. torque to the rear wheels.

Perfect Fit:

Tube lines up directly to factory intercooler and comes with silicone couplers for an OE quality seal and fit.

Flow and Performance:

Constructed of 3″-3 1/2″ smooth aluminum tubing for maximum flow. Smooth transition mandrel bends reduce turbulence while increasing horsepower and torque.

Installation is a snap
:
Simple and clean installation. Every aFe charge pipe comes with all the necessary hardware.

*Legal in California only for racing vehicles which may never be used upon highway.

Place your order
Contact your LAUNCH Sales rep for pricing at (626) 839-7150.

aFe POWER: Magnum Force Intake System for 2011up BMW 335i

LAUNCH Distribution introduces the Magnum FORCE Stage-2 Si Intake System for the BMW 335i (E90/92/93) 11-13 L6-3.0L (t) N55 from aFe Power.

Part number: 54-81912

This all new Sealed Intake System produced 9hp and 14lbs. x ft. torque and outflows the factory intake by 20%. This system uses a PRO 5R progressive weave filter for maximum airflow and increased performance. This unique sealed air intake system uses a one piece rotomolded air intake tube that snaps onto the factory lower air box for a quick hassle free installation. The lower air box retains your factory ram air scoop to keep cool air flowing for maximum power gains. This installation takes approximately 20 minutes and comes complete will all necessary hardware.

3-1/2″ Tall Conical Pro 5R Air Filter: This intake utilizes a huge, 3-1/2″ tall conical PRO 5R performance air filter with inverted top for increased performance. The PRO 5R air filter uses five layers of progressively finer mesh cotton gauze media to provide maximum airflow for best performance results. Washable and reusable for multiple cleaning cycles, the tall, open, evenly spaced pleats provide excellent dust holding capacity for a longer service cycle between cleanings.

One-Piece Rotomolded Intake Tube: A one piece rotomolded tube is used to retain your factory lower air box. The lower air box retains your factory ram air scoop which provides constant cool air and keeps warm engine air out for maximum performance. This one-piece intake tube uses factory mounting locations for a hassle-free installation.

Dyno Tested Intake Tube: The intake tube is designed to maximize air velocity and is dyno and flow tested using the latest engineering tools for maximum performance, mileage and throttle response.

Also Fits:
BMW 135i (E82/88) 11-13 L6-3.0L (Turbo) N55

Place your order
Call your LAUNCH Sales Rep for pricing and availability today at (626) 839-7150.

Don't have an account yet?

Sign up today. It's free and you'll be able to see how much money you'd be saving by utilizing LAUNCH Distribution for your inventory purchases.

Sign Me Up!