News

AEM Electronics: Wideband Failsafe Gauge

The Wideband FAILSAFE Gauge provides the ability to accurately tune AFR, while actively protecting your engine by constantly monitoring AFR curves and activating a user-defined failsafe strategy if it runs lean.

The Wideband FAILSAFE Gauge is a Universal Exhaust Gas Oxygen (UEGO—“you-way-go”) controller with an internal boost sensor, an internal data logger and a full color Organic Light Emitting Diode (OLED) display. It includes technology to activate a failsafe strategy in the event AFR falls outside of a user-defined operating window. If the AFR falls outside of the set operating window, the Wideband FAILSAFE Gauge triggers a user defined output function that can save an engine from catastrophic damage.

WHY YOU WANT ONE
This product is a must have for all tuned performance engines, either forced induction or naturally aspirated, fuel injected or carbureted. Any high performance vehicle owners who want a highly accurate AFR tuning tool with logging and a protection strategy that can save an engine from catastrophic failure will want this FAILSAFE device.

WHAT IT DOES
After the engine is tuned and a safe operating window of AFR is established, the Wideband FAILSAFE Gauge continually monitors AFR and boost or vacuum to make sure that AFR does not fall out of the defined operating window at a given boost or vacuum level. If the Wideband Failsafe detects an out of range AFR reading, the gauge triggers a low side output (ground signal with a 1.5 amp draw max) that can save your engine from catastrophic damage.

Use the gauge’s intuitive software to configure the low side output, create a user-adjustable time delay strategy to prevent false alarms, and customize the gauge lighting to flash and alert the driver if an alarm is triggered.

WHY USE A WIDEBAND AIR/FUEL CONTROLLER?
Accurate AFR data is critical when tuning an engine. Running rich (very low air/fuel ratio, excessive fuel) can cause a loss in power and fuel economy, while running too lean (very high air/fuel ratio, not enough fuel) may result in serious engine damage. Using a wideband air/fuel controller during the tuning process allows you to monitor AFR and adjust tuning parameters to optimize them for maximum power and efficiency.

The Wideband FAILSAFE Gauge is an ideal engine tuning tool. The highly accurate Bosch AFR wideband sensor is maintenance free and never requires free-air calibration, enabling you to fine tune AFR from an AEM programmable engine management system, any other programmable EMS or piggyback programmer. For carbureted applications, it can tell you when it’s time to swap carb(s), change jets or simply modify fuel pressure.

aFe Power: Intake for 2012 F-150 V6

This Stage 2 air Intake system produces an astonishing 33 horsepower and 34lbs. x ft. torque and outflows the factory intake by 44%! This intake is the most sophisticated design on the market today. The equal length dual tube design with an H-pipe balance tube increases intake air flow and velocity increasing horsepower and improving throttle response and turbo spool times. Enclosed in a durable 16-gauge heat shield that uses the lower half of the factory air box, two 360 degree conical Pro 5R air filter for maximum flows. The one-piece heat shield requires no assembly and the filter is constructed with 100% polyurethane for long life and multiple cleaning cycles.

Equal Length Intake Tube – This intake uses a dual intake tube design with an H-Pipe balance tube to balance intake tube pressures and maximize air flow and velocity.

Dual 360 Degree Air Filters– This intake utilizes dual oval conical Pro 5R performance air filters for maximum flow. This 5-layer progressive, oiled cotton gauze air filter provides maximum flow for increased horsepower and torque.

Top Mounted Heat Shield Design– aFe developed this heat shield to snap onto the top of the lower half of the factory air box to provide a hassle-free installation utilizing factory mounting locations.

Cold Air Intake System
Magnum FORCE Intake System; Stage 2 Pro 5R; Ford F-150 EcoBoost; 2012 V6-3.5L (tt)
P/N 54-12192

Eibach PRO-KIT: 2013 FRS & BRZ

Launch Distribution is proud to announce the release of Eibach Pro-Kit for the 2013 Scion FR-S and Subaru BRZ.

Eibach USA releases the PRO-KIT for 2013 Scion FRS and Subaru BRZ. PRO-KIT lowers your FR-S & BRZ’s center of gravity, reducing squat during acceleration,
body roll in corners and excessive nose-dive under braking. When combined with Plus-1 or Plus-2 wheels and tires, the Eibach PRO-KIT is the finishing touch to a winning recipe for performance. PRO-KIT also reduces excessive fender-well clearance, making your car look just as hot as it performs.

Click the link below for complete details.
Specification Guide

Place your order
Call your Launch Sales Representative for pricing at (626) 839-7150 today!

Don't have an account yet?

Sign up today. It's free and you'll be able to see how much money you'd be saving by utilizing LAUNCH Distribution for your inventory purchases.

Sign Me Up!